| 73063L Franke Slewing Ring Bearings | Factor fo:15.4; Static Load Rating:186,000 N; Enclosure:Double Shield; B:48 mm; Dynamic Load Rating:185,000 N; d:160 mm; Radial Clearance:0.046 to 0.091 mm; Limiting Speed - Grease:2,100 rpm; D:290 mm; da (min):174 mm; Weight:14.300 kg; Da (max):276 mm; ra (max):2.5 mm; Fillet Radius/Chamfer:3 mm; Bore Type:Cylindrical Bore; Configuration:Single Row; |
| 26 0741 01 Rollix Slewing Ring Bearings | Da - Cup Frontface Backing Diameter:54.10 mm; Cup Part Number:1930; Ab - Cage-Cone Frontface Clearance:2 mm; Y - ISO Factor9:1.82; Ca90 - Dynamic Thrust Rating (90 million revolutions)6:1590 lbf; G2 - Heat Generation Factor (Rib-Roller End):6.3; Cone Part Number:1975; e - ISO Factor8:0.33; Cage Type:Stamped Steel; Series:1900; Cg - Geometry Factor:0.0565; D:56.896 mm; Db - Cup Backface Backing Diameter:51.05 mm; |
| 73082L Franke Slewing Ring Bearings | B:58 mm; da (min):148 mm; Db (max):247 mm; Limiting Speed - Oil:2,600 rpm; r1:4 mm; Fillet Radius/Chamfer:4 mm; Da (max):262 mm; db (min):148 mm; Limiting Speed - Grease:2,200 rpm; Radial Clearance:0.060 to 0.105 mm; Enclosure:Open; Bore Type:Cylindrical Bore; D:280 mm; Outside Ring Inside Diameter:243 mm; Db (min):262 mm; ra (max):3 mm; Dynamic Load Rating:555,000 N; dc (min):169 mm; Static Load Rating:665,000 N; |
| 37 0841 01 Rollix Slewing Ring Bearings | Ab - Cage-Cone Frontface Clearance:0.12 in; Aa - Cage-Cone Backface Clearance:0.19 in; r - Cup Frontface To Clear Radius2:0.06 in; R - Cone Backface To Clear Radius1:0.080 in; C1 - Dynamic Radial Rating (Two-Row, 1 million revolutions)4:46500 lbf; C90 - Dynamic Radial Rating (One-Row, 90 million revolutions)3:6920 lbf; Series:53000; G2 - Heat Generation Factor (Rib-Roller End):9.63; Y2 - ISO Factor10:1.36; |
| 6 2500 01 Rollix Slewing Ring Bearings | Bore Type:Cylindrical Bore; ra:1 mm; d:40 mm; B:30.2 mm; Limiting Speed - Oil:8,000 rpm; Cy:4.7 mm; Radial Clearance:0.015 to 0.033 mm; Da:73 mm; Configuration:Double Row; Snap Ring Outside Diameter:86.6 mm; Dynamic Load Rating:45,500 N; Limiting Speed - Grease:6,000 rpm; Snap Ring Width:1.7 mm; da:47 mm; a (max):3.3 mm; Fillet Radius/Chamfer:1.1 mm; Weight:0.570 kg; Static Load Rating:34,000 N; Dx:88 mm; |
| 75018A Franke Slewing Ring Bearings | Dimension V:3.0 in; Note:This product line wa; Shaft Size:1.5 in; Series Type:Light Series; Dimension U:0.2 in; Seal Type:Felt Seal; Bearing Type:Split Cylindrical Re; Support Type:Take-Up; Maximum Speed:5400 rpm; Dimension N:6.8 in; Dimension B:4.0 in; Dimension Y:0.5 in; Tensioning Unit Type:Push Type; Bearing Number:LSE108BR; Dimension D:6.0 in; Bearing UPC:013992025401; Bearing - Housing - Seal:LSE108BRH; |
| 73107L Franke Slewing Ring Bearings | C90 - Dynamic Radial Rating (90 million revolutions)4:67200 lbf; Cup Part Number:HH234010; D:307.975 mm; e - ISO Factor8:0.33; C0 - Static Radial Rating:354000 lbf; C1 - Dynamic Radial Rating (1 million revolutions)5:259000 lbf; r - Cup Backface To Clear Radius2:6.86 mm; Design Units:Imperial; K - Factor7:1.79; Ab - Cage-Cone Frontface Clearance:1.8 mm; da - Cone Frontface Backing Diameter:167.89 mm; |
| 75010A Franke Slewing Ring Bearings | Dimension M:15.0 in; Dimension H:21.654 in; Pillow/Plummer Block Style:Split Cylindrical Ho; Support Type:Eight-Bolt Plummer B; Dimension H2:45.9 in; Cor - Static Load Rating:1486212 lbf; Shipping Weight:5331 lb; Maximum Speed:340 rpm; Dimension J1:42.5 in; Dimension H1:3.7 in; Bearing UPC:013992054487; Bearing Number:HSE1800BR; Bearing Type:Split Cylindrical Re; Cr - Dynamic Load Rating:855848 lbf; |
| 66159L Franke Slewing Ring Bearings | Weight:149 lb; Locking Style:Double Concentric; Dimension J (Bolt Size):1.125 in; C - Dynamic Load (Basic):170000 lb; Dimension M:3.72 in; Dimension H:2.00 in; Full Timken Part Number:QAAPX26A130SB; Shaft Tolerance:0.0050 in; Dimension R:1.47 in; Y1 - Geometry Factor:2.62; Dimension A:6.13 in; Dimension S:7.440 in; Pre Install Clearance Min:0.0037 in; Grease Lubrication - B/C/O Seal:400 rpm; Dimension D Min:15.25 in; |
| 66153L Franke Slewing Ring Bearings | Design Units:METRIC; K - Factor2:1.29; r - Cup Backface To Clear Radius1:2.03 mm; G2 - Heat Generation Factor (Rib-Roller End):37.4; Cg - Geometry Factor:0.109; G1 - Heat Generation Factor (Roller-Raceway):69.7; Da - Cup Frontface Backing Diameter:119.90 mm; Y - ISO Factor4:1.33; Series:JP8000; Cup Part Number:JP8010; C - Cup Width:17.500 mm; D:125 mm; e - ISO Factor3:0.45; Db - Cup Backface Backing Diameter:115.06 mm; |